View 74LVC2245A_19354.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

INTEGRATED CIRCUITS
DATA SHEET
74LVC2245A Octal transceiver with direction pin; 30 series termination resistors; 5 V input/output tolerant; 3-state
Product specification Supersedes data of 1999 Mar 23 File under Integrated Circuits, IC24 1999 Jun 15
Philips Semiconductors
Product specification
Octal transceiver with direction pin; 30 series termination resistors; 5 V input/output tolerant; 3-state
FEATURES * 5 V tolerant inputs/outputs for interfacing with 5 V logic * Wide supply voltage range of 1.2 to 3.6 V * CMOS low power consumption * Direct interface with TTL levels * Integrated 30 termination resistors DESCRIPTION
74LVC2245A
The 74LVC2245A is a high-performance, low-power, low-voltage, Si-gate CMOS device, superior to most advanced CMOS compatible TTL families. Inputs can be driven from either 3.3 or 5 V devices. In 3-state operation, outputs can handle 5 V. These features allow the use of these devices as translators in a mixed 3.3 V/5 V environment. The 74LVC2245A is an octal transceiver featuring non-inverting 3-state bus compatible outputs in both send and receive directions. The `245' features an output enable (OE) input for easy cascading and a send/receive (DIR) input for direction control OE controls the outputs so that the buses are effectively isolated. The 74LVC2245A is designed with 30 series termination resistors in both HIGH and LOW output stages to reduce line noise.
FUNCTION TABLE See note 1. INPUT OE L L H Note 1. H = HIGH voltage level; L = LOW voltage level; X = don't care; Z = high-impedance OFF-state. ORDERING INFORMATION PACKAGE OUTSIDE NORTH AMERICA 74LVC2245AD 74LVC2245ADB 74LVC2245APW NORTH AMERICA 74LVC2245AD 74LVC2245ADB 74LVC2245APW DH TEMPERATURE RANGE -40 to +85 C PINS 20 20 20 PACKAGE MATERIAL SO SSOP TSSOP plastic plastic plastic CODE SOT163-1 SOT339-1 SOT360-1 DIR L H X An A=B inputs Z INPUT/OUTPUT Bn inputs B=A Z
1999 Jun 15
2
Philips Semiconductors
Product specification
Octal transceiver with direction pin; 30 series termination resistors; 5 V input/output tolerant; 3-state
QUICK REFERENCE DATA GND = 0 V; Tamb = 25 C; tr = tf 2.5 ns. SYMBOL tPHL/tPLH CI CPD Note 1. CPD is used to determine the dynamic power dissipation (PD in W). PD = CPD x VCC2 x fi + (CL x VCC2 x fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in V; (CL x VCC2 x fo) = sum of the outputs. PINNING PIN 1 2, 3, 4, 5, 6, 7, 8, 9 10 18, 17, 16, 15, 14, 13, 12, 11 19 20 DIR A0 to A7 GND B0 to B7 OE VCC SYMBOL PARAMETER propagation delay An to Bn; Bn to An input capacitance power dissipation capacitance per buffer VI = GND to VCC; note 1 CONDITIONS CL = 50 pF; VCC = 3.3 V
74LVC2245A
TYPICAL 3.9 5.0 27 ns pF pF
UNIT
DESCRIPTION direction control data inputs/outputs ground (0 V) data inputs/outputs output enable input (active LOW) DC supply voltage
1999 Jun 15
3
Philips Semiconductors
Product specification
Octal transceiver with direction pin; 30 series termination resistors; 5 V input/output tolerant; 3-state
74LVC2245A
handbook, halfpage
DIR 1 A0 2 A1 3 A2 4 A3 5 A4 6 A5 7 A6 8 A7 9 GND 10
MNA363
20 VCC 19 OE 18 B0 17 B1 16 B2
2245
15 B3 14 B4 13 B5 12 B6 11 B7
handbook, halfpage
1
DIR OE
19
2
A0 B0 18
3
A1 B1 17
4
A2 B2 A3 16
Fig.1 Pin configuration.
5
B3 6 A4 B4
handbook, halfpage
15
14
19 1
G3 3EN1 (BA) 3EN2 (AB)
7
A5 B5 13
8 1 2 3 4 5 6 7 8 9
MNA365
A6 B6 12
2
18 17 16 15 14 13 12 11
9
A7 B7 11
MNA364
Fig.3 IEC logic symbol.
Fig.2 Logic symbol.
1999 Jun 15
4
Philips Semiconductors
Product specification
Octal transceiver with direction pin; 30 series termination resistors; 5 V input/output tolerant; 3-state
RECOMMENDED OPERATING CONDITIONS
74LVC2245A
LIMITS SYMBOL VCC PARAMETER DC supply voltage (for max. speed performance) DC supply voltage (for low-voltage applications) VI VO DC input voltage range DC output voltage range; output HIGH or LOW state DC output voltage range; 3-state Tamb tr,tf operating ambient temperature range input rise and fall times see DC and AC characteristics per device VCC = 1.2 to 2.7 V VCC = 2.7 to 3.6 V CONDITIONS MIN. 2.7 1.2 0 0 0 -40 0 0 MAX. 3.6 3.6 5.5 VCC 5.5 +85 20 10 V V V V V C ns/V UNIT
LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). Voltages are referenced to GND (ground = 0 V). SYMBOL VCC IIK VI IOK VO PARAMETER DC supply voltage DC input diode current DC input voltage DC output diode current DC output voltage; output HIGH or LOW DC output diode current DC VCC or GND current storage temperature range power dissipation per package plastic mini-pack (SO) above +70 C derate linearly with 8 mW/K - - 500 500 mW mW plastic shrink mini-pack (SSOP above +60 C derate linearly with and TSSOP) 5.5 mW/K Note 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. VI < 0 note 1 VO > VCC or VO < 0 note 1 CONDITIONS MIN. -0.5 - -0.5 - -0.5 -0.5 - - -65 MAX. +6.5 -50 +5.5 50 UNIT V mA V mA
VCC + 0.5 V +6.5 50 100 +150 V mA mA C
DC output voltage; output 3-state note 1 IO IGND, ICC Tstg Ptot VO = 0 to VCC
1999 Jun 15
5
Philips Semiconductors
Product specification
Octal transceiver with direction pin; 30 series termination resistors; 5 V input/output tolerant; 3-state
DC CHARACTERISTICS Over recommended operating conditions; voltage are referenced to GND (ground = 0 V). TEST CONDITIONS SYMBOL PARAMETER OTHER VIH VIL VOH HIGH-level input voltage LOW-level input voltage HIGH-level output voltage VI = VIH or VIL; IO = -6 mA VI = VIH or VIL; IO = -12 mA VOL LOW-level output voltage VI = VIH or VIL; IO = 6 mA VI = VIH or VIL; IO = 100 A VI = VIH or VIL; IO = 12 mA II IOZ Ioff ICC ICC Note 1. All typical values are at VCC = 3.3 V and Tamb = 25 C. input leakage current 3-state output OFF-state current power off leakage supply quiescent supply current additional quiescent supply current per control pin VI = 5.5 V or GND VI = VIH or VIL; VO = 5.5 V or GND VI or VO = 5.5 V VI = VCC or GND; IO = 0 VI = VCC - 0.6 V; IO = 0 VCC (V) 1.2 1.2 2.7 3.0 2.7 3.0 3.0 3.6 3.6 0.0 3.6 MIN. VCC -
74LVC2245A
Tamb (C) -40 to +85 TYP.(1) - - - - MAX. - - GND 0.8 - - - 0.40 0.20 0.55 5 10 10 20 500 A A A A A V V V V UNIT
2.7 to 3.6 2.0 2.7 to 3.6 - VI = VIH or VIL; IO = -100 A 3.0
VCC - 0.5 - VCC - 0.2 VCC VCC - 0.8 - - - - - - - - - - - 0.1 0.1 0.1 0.1 5
2.7 to 3.6 -
1999 Jun 15
6
Philips Semiconductors
Product specification
Octal transceiver with direction pin; 30 series termination resistors; 5 V input/output tolerant; 3-state
AC CHARACTERISTICS GND = 0 V; tr = tf 2.5 ns. LIMITS SYMBOL PARAMETER WAVEFORMS VCC = 3.3 V 0.3 V MIN. tPHL/tPLH tPZH/tPZL tPHZ/tPLZ Note 1. Typical values at VCC = 3.3 V and Tamb = 25 C. AC WAVEFORMS propagation delay An to Bn; Bn to An 3-state output enable time OE to An; OE to Bn 3-state output disable time OE to An; OE to Bn see Figs 4 and 6 see Figs 5 and 6 see Figs 5 and 6 1.5 1.5 1.5 TYP.(1) 3.9 5.7 4.2 MAX. 6.5 9.0 5.9
74LVC2245A
VCC = 2.7 V MIN. 1.5 1.5 1.5 MAX. 7.5 10.0 6.9
UNIT
ns ns ns
handbook, halfpage VI
An, Bn INPUT GND tPHL VOH Bn, An OUTPUT VOL
VM
tPLH
VM
MNA366
VM = 1.5 V at VCC 2.7 V; VM = 0.5 VCC at VCC < 2.7 V; VOL and VOH are typical output voltage drop that occur with the output load.
Fig.4
The input An to output Yn propagation delays.
1999 Jun 15
7
Philips Semiconductors
Product specification
Octal transceiver with direction pin; 30 series termination resistors; 5 V input/output tolerant; 3-state
74LVC2245A
handbook, full pagewidth
VI OE INPUT GND tPLZ VCC OUTPUT LOW-to-OFF OFF-to-LOW VOL tPHZ VOH OUTPUT HIGH-to-OFF OFF-to-HIGH GND outputs enabled VY VM VM VX tPZH tPZL VM
outputs disabled
outputs enabled
MNA367
VM = 1.5 V at VCC 2.7 V; VM = 0.5VCC at VCC < 2.7 V; VX = VOL + 0.3 V at VCC 2.7 V; VX = VOL + 0.1 V at VCC < 2.7 V;
VY = VOH - 0.3 V at VCC 2.7 V; VY = VOH - 0.1 V at VCC < 2.7 V; VOL and VOH are typical output voltage drop that occur with the output load.
Fig.5 The 3-state enable and disable times.
handbook, full pagewidth
S1 VCC PULSE GENERATOR VI D.U.T. RT CL 50 pF RL 500 VO RL 500
2 x VCC open GND
MNA368
TEST tPLH/tPHL tPLZ/tPZL tPHZ/tPZH
S1 open 2 x VCC GND VCC <2.7 V 2.7 to 3.6 V VI VCC 2.7 V
Definitions for test circuit: RL = Load resistor; see Chapter "AC characteristics". CL = Load capacitance including jig and probe capacitance (see Chapter "AC characteristics"). RT = Termination resistance should be equal to the output Impedance Z0 of the pulse generator.
Fig.6 Load circuitry for switching times.
1999 Jun 15
8
Philips Semiconductors
Product specification
Octal transceiver with direction pin; 30 series termination resistors; 5 V input/output tolerant; 3-state
PACKAGE OUTLINES SO20: plastic small outline package; 20 leads; body width 7.5 mm
74LVC2245A
SOT163-1
D
E
A X
c y HE vMA
Z 20 11
Q A2 A1 pin 1 index Lp L 1 e bp 10 wM detail X (A 3) A
0
5 scale
10 mm
DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. OUTLINE VERSION SOT163-1 REFERENCES IEC 075E04 JEDEC MS-013AC EIAJ EUROPEAN PROJECTION A max. 2.65 0.10 A1 0.30 0.10 A2 2.45 2.25 A3 0.25 0.01 bp 0.49 0.36 c 0.32 0.23 D (1) 13.0 12.6 0.51 0.49 E (1) 7.6 7.4 0.30 0.29 e 1.27 0.050 HE 10.65 10.00 L 1.4 Lp 1.1 0.4 Q 1.1 1.0 0.043 0.039 v 0.25 0.01 w 0.25 0.01 y 0.1 0.004 Z
(1)
0.9 0.4 0.035 0.016
0.012 0.096 0.004 0.089
0.019 0.013 0.014 0.009
0.419 0.043 0.055 0.394 0.016
8o 0o
ISSUE DATE 95-01-24 97-05-22
1999 Jun 15
9
Philips Semiconductors
Product specification
Octal transceiver with direction pin; 30 series termination resistors; 5 V input/output tolerant; 3-state
74LVC2245A
SSOP20: plastic shrink small outline package; 20 leads; body width 5.3 mm
SOT339-1
D
E
A X
c y HE vMA
Z 20 11
Q A2 pin 1 index A1 (A 3) Lp L 1 e bp 10 wM detail X A
0
2.5 scale
5 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A max. 2.0 A1 0.21 0.05 A2 1.80 1.65 A3 0.25 bp 0.38 0.25 c 0.20 0.09 D (1) 7.4 7.0 E (1) 5.4 5.2 e 0.65 HE 7.9 7.6 L 1.25 Lp 1.03 0.63 Q 0.9 0.7 v 0.2 w 0.13 y 0.1 Z (1) 0.9 0.5 8 0o
o
Note 1. Plastic or metal protrusions of 0.20 mm maximum per side are not included. OUTLINE VERSION SOT339-1 REFERENCES IEC JEDEC MO-150AE EIAJ EUROPEAN PROJECTION
ISSUE DATE 93-09-08 95-02-04
1999 Jun 15
10
Philips Semiconductors
Product specification
Octal transceiver with direction pin; 30 series termination resistors; 5 V input/output tolerant; 3-state
74LVC2245A
TSSOP20: plastic thin shrink small outline package; 20 leads; body width 4.4 mm
SOT360-1
D
E
A
X
c y HE vMA
Z
20
11
Q A2 pin 1 index A1 (A 3) A
Lp L
1
e bp
10
wM detail X
0
2.5 scale
5 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.10 A1 0.15 0.05 A2 0.95 0.80 A3 0.25 bp 0.30 0.19 c 0.2 0.1 D (1) 6.6 6.4 E (2) 4.5 4.3 e 0.65 HE 6.6 6.2 L 1.0 Lp 0.75 0.50 Q 0.4 0.3 v 0.2 w 0.13 y 0.1 Z (1) 0.5 0.2 8 0o
o
Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT360-1 REFERENCES IEC JEDEC MO-153AC EIAJ EUROPEAN PROJECTION ISSUE DATE 93-06-16 95-02-04
1999 Jun 15
11
Philips Semiconductors
Product specification
Octal transceiver with direction pin; 30 series termination resistors; 5 V input/output tolerant; 3-state
SOLDERING Introduction to soldering surface mount packages This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "Data Handbook IC26; Integrated Circuit Packages" (document order number 9398 652 90011). There is no soldering method that is ideal for all surface mount IC packages. Wave soldering is not always suitable for surface mount ICs, or for printed-circuit boards with high population densities. In these situations reflow soldering is often used. Reflow soldering Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Several methods exist for reflowing; for example, infrared/convection heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 and 200 seconds depending on heating method. Typical reflow peak temperatures range from 215 to 250 C. The top-surface temperature of the packages should preferable be kept below 230 C. Wave soldering Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. To overcome these problems the double-wave soldering method was specifically developed.
74LVC2245A
If wave soldering is used the following conditions must be observed for optimal results: * Use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave. * For packages with leads on two sides and a pitch (e): - larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; - smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves at the downstream end. * For packages with leads on four sides, the footprint must be placed at a 45 angle to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves downstream and at the side corners. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical dwell time is 4 seconds at 250 C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. Manual soldering Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 C.
1999 Jun 15
12
Philips Semiconductors
Product specification
Octal transceiver with direction pin; 30 series termination resistors; 5 V input/output tolerant; 3-state
Suitability of surface mount IC packages for wave and reflow soldering methods SOLDERING METHOD PACKAGE WAVE BGA, SQFP HLQFP, HSQFP, HSOP, SMS PLCC(3), SO, SOJ LQFP, QFP, TQFP SSOP, TSSOP, VSO Notes not suitable not suitable(2) suitable not recommended(3)(4) not recommended(5) suitable suitable suitable suitable suitable
74LVC2245A
REFLOW(1)
1. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the "Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods". 2. These packages are not suitable for wave soldering as a solder joint between the printed-circuit board and heatsink (at bottom version) can not be achieved, and as solder may stick to the heatsink (on top version). 3. If wave soldering is considered, then the package must be placed at a 45 angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. 4. Wave soldering is only suitable for LQFP, TQFP and QFP packages with a pitch (e) equal to or larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. 5. Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. DEFINITIONS Data sheet status Objective specification Preliminary specification Product specification Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. This data sheet contains target or goal specifications for product development. This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains final product specifications.
1999 Jun 15
13
Philips Semiconductors
Product specification
Octal transceiver with direction pin; 30 series termination resistors; 5 V input/output tolerant; 3-state
NOTES
74LVC2245A
1999 Jun 15
14
Philips Semiconductors
Product specification
Octal transceiver with direction pin; 30 series termination resistors; 5 V input/output tolerant; 3-state
NOTES
74LVC2245A
1999 Jun 15
15
Philips Semiconductors - a worldwide company
Argentina: see South America Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113, Tel. +61 2 9805 4455, Fax. +61 2 9805 4466 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 1 60 101 1248, Fax. +43 1 60 101 1210 Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, 220050 MINSK, Tel. +375 172 20 0733, Fax. +375 172 20 0773 Belgium: see The Netherlands Brazil: see South America Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor, 51 James Bourchier Blvd., 1407 SOFIA, Tel. +359 2 68 9211, Fax. +359 2 68 9102 Canada: PHILIPS SEMICONDUCTORS/COMPONENTS, Tel. +1 800 234 7381, Fax. +1 800 943 0087 China/Hong Kong: 501 Hong Kong Industrial Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Tel. +852 2319 7888, Fax. +852 2319 7700 Colombia: see South America Czech Republic: see Austria Denmark: Sydhavnsgade 23, 1780 COPENHAGEN V, Tel. +45 33 29 3333, Fax. +45 33 29 3905 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. +358 9 615 800, Fax. +358 9 6158 0920 France: 51 Rue Carnot, BP317, 92156 SURESNES Cedex, Tel. +33 1 4099 6161, Fax. +33 1 4099 6427 Germany: Hammerbrookstrae 69, D-20097 HAMBURG, Tel. +49 40 2353 60, Fax. +49 40 2353 6300 Hungary: see Austria India: Philips INDIA Ltd, Band Box Building, 2nd floor, 254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025, Tel. +91 22 493 8541, Fax. +91 22 493 0966 Indonesia: PT Philips Development Corporation, Semiconductors Division, Gedung Philips, Jl. Buncit Raya Kav.99-100, JAKARTA 12510, Tel. +62 21 794 0040 ext. 2501, Fax. +62 21 794 0080 Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. +353 1 7640 000, Fax. +353 1 7640 200 Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053, TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007 Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3, 20124 MILANO, Tel. +39 02 67 52 2531, Fax. +39 02 67 52 2557 Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108-8507, Tel. +81 3 3740 5130, Fax. +81 3 3740 5057 Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. +82 2 709 1412, Fax. +82 2 709 1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. +60 3 750 5214, Fax. +60 3 757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +9-5 800 234 7381, Fax +9-5 800 943 0087 Middle East: see Italy Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. +31 40 27 82785, Fax. +31 40 27 88399 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. +64 9 849 4160, Fax. +64 9 849 7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. +47 22 74 8000, Fax. +47 22 74 8341 Pakistan: see Singapore Philippines: Philips Semiconductors Philippines Inc., 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474 Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA, Tel. +48 22 612 2831, Fax. +48 22 612 2327 Portugal: see Spain Romania: see Italy Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW, Tel. +7 095 755 6918, Fax. +7 095 755 6919 Singapore: Lorong 1, Toa Payoh, SINGAPORE 319762, Tel. +65 350 2538, Fax. +65 251 6500 Slovakia: see Austria Slovenia: see Italy South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 58088 Newville 2114, Tel. +27 11 471 5401, Fax. +27 11 471 5398 South America: Al. Vicente Pinzon, 173, 6th floor, 04547-130 SAO PAULO, SP, Brazil, Tel. +55 11 821 2333, Fax. +55 11 821 2382 Spain: Balmes 22, 08007 BARCELONA, Tel. +34 93 301 6312, Fax. +34 93 301 4107 Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM, Tel. +46 8 5985 2000, Fax. +46 8 5985 2745 Switzerland: Allmendstrasse 140, CH-8027 ZURICH, Tel. +41 1 488 2741 Fax. +41 1 488 3263 Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2886, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260, Tel. +66 2 745 4090, Fax. +66 2 398 0793 Turkey: Yukari Dudullu, Org. San. Blg., 2.Cad. Nr. 28 81260 Umraniye, ISTANBUL, Tel. +90 216 522 1500, Fax. +90 216 522 1813 Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7, 252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461 United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes, MIDDLESEX UB3 5BX, Tel. +44 208 730 5000, Fax. +44 208 754 8421 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel. +1 800 234 7381, Fax. +1 800 943 0087 Uruguay: see South America Vietnam: see Singapore Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD, Tel. +381 11 62 5344, Fax.+381 11 63 5777
For all other countries apply to: Philips Semiconductors, International Marketing & Sales Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825 (c) Philips Electronics N.V. 1999
Internet: http://www.semiconductors.philips.com
SCA 66
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
245004/02/pp16
Date of release: 1999 Jun 15
Document order number:
9397 750 05624

▲Up To Search▲

Price & Availability of 74LVC2245A

	To Download 74LVC2245A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .